| Topologie | Abwärtswandler |
| Eingangsspannung | 450-780 V |
| Ausgang 1 | 390 V / 1.5 A |
| IC-Revision | 1 |
This reference design converts a DC-input source in the range of 450 V to 780 V into non-isolated 390 V at 1.5A. This is an alternative solution to SiC-FET and SiC-Diode Buck converter, since the actual power stage uses only standard silicon components. In order to employ 600 V rated devices, the input source has been split so that two identical buck stages share the center point. A single coupled inductor (1:1) balances automatically the center point. Two small-series inductors limit the current in each branch in case of voltage imbalance and any small variation in the gate drive delay time of the two FETs. The converter minimizes the switching loss as a result of CRM mode (critical conduction mode), achieving peak efficiency of 99% at 450 V input voltage and full load.
Artikel Nr. | Datenblatt | Simulation | Downloads | Status | Produktserie | C | Tol. C | VR(V (DC)) | Bauform | Betriebstemperatur | DF(%) | RISO | Keramiktyp | L(mm) | B(mm) | H(mm) | Fl(mm) | Verpackung | Vin | VOut1(V (DC)) | IOut1(A) | Isolierungstyp | fswitch(kHz) | ∫Udt(Vµs) | NPRI : NSEC | L(µH) | VT(V (AC)) | Montageart | Muster | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| WCAP-CSGP MLCCs 50 V(DC), 1 nF, ±10% | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 50 V(DC) | Kapazität1 nF | Kapazität±10% | Nennspannung50 V (DC) | Bauform0603 | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor2.5 % | Isolationswiderstand10 GΩ | KeramiktypX7R Klasse II | Länge1.6 mm | Breite0.8 mm | Höhe0.8 mm | Pad Dimension0.4 mm | Verpackung7" Tape & Reel | – | – | – | – | – | – | – | – | – | – | |||||
![]() | WE-PPTI Push-Pull Transformers, –, – | Simulation– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWE-PPTI Push-Pull Transformers | – | – | – | Bauform1006 | Betriebstemperatur -40 °C up to +125 °C | – | – | – | Länge6.73 mm | Breite10.2 mm | Höhe4.19 mm | – | VerpackungTape and Reel | Input Voltage 5 V (DC) | Ausgangsspannung 15 V (DC) | Ausgangsstrom 10.6 A | IsolierungstypFunktional | Switching Frequency 300 - 620 | Spannung-µSekunde11 Vµs | Übersetzungsverhältnis1:1.3 | Induktivität475 µH | Prüfspannung2500 V (AC) | MontageartSMT | |||
750317489 | PFC Inductor, –, – | Simulation– | Downloads– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | Produktserie PFC Inductor | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |