IC-Hersteller STMicroelectronics

IC-Hersteller (103)

STMicroelectronics STCH03L | Demoboard EVLSTCH03-36W-SR

36W USB charger with selectable output voltage (5-9-12 V @3A) based on STCH03L and SRK1000B

Details

TopologieSperrwandler
Eingangsspannung90-264 V
Ausgang 112 V / 3 A
IC-Revision1

Beschreibung

The EVLSTCH03-36W-SR shown in the image here is a 36 W wide-range mains USB charger demonstration board, with selectable output voltage (5 - 9 - 12 V @ 3 A output current), based on the STCH03L and SRK1000B. The power circuit is a quasi-resonant (QR) flyback converter, with peak current mode control, based on the STCH03L IC. The circuit operates with secondary side constant voltage (CV) regulation through an optocoupler and is capable of providing constant output current (CC) regulation using primary sensing feedback. The STCH03L embeds a 650 V, non-dissipative, HV startup cell, which, along with the extremely low quiescent current and burst-mode management, helps minimize residual input consumption, thus achieving less than 20 mW under no-load condition. At secondary side, the SRK1000B controller implements synchronous rectification to increase system efficiency: it controls the synchronous rectifier MOSFET, driving its gate with minimal turn-on delay and maximizing the turn-off time instant (through an adaptive mechanism) so that the residual conduction of the SR MOSFET body diode after turn-off reduces to the target value of 300 ns. The charger is designed to meet the most stringent energy saving recommendations (Eu CoC rev. 5 - Tier 2 and EPS of DOE USA) as well as EMI regulation EN55022-Class-B for line conducted noise emissions.

Eigenschaften

  • Universal AC mains input voltage range: 90 V to 264 V
  • Output voltage: 5 - 9 - 12 V selectable @3 A continuous operation
  • Constant voltage (CV) regulation with optocoupler and constant current (CC) regulation with primary side sensing
  • No-load consumption < 20mW at 230 VAC (with load disconnected from charger)
  • 4 points average efficiency and 10% load efficiency in compliance with Eu CoC rev. 5 - Tier 2 (2016)
  • Line conducted EMI in compliance with EN55022 - Class B
  • Small form factor (73 x 55 x 15 mm)
  • RoHS compliant

Weiterführende Informationen

Artikeldaten

Artikel Nr.
Daten­blatt
Simu­lation
Downloads
Status
Produktserie
L(µH)
IR 1(mA)
IR 2(mA)
ISAT(mA)
RDC(mΩ)
fres(MHz)
Typ
H(mm)
B(mm)
IR(A)
ISAT,10%(A)
RDC max.(mΩ)
Version
Interface typ
Ausführung
Gender
Pins
Montageart
Arbeitsspannung(V (AC))
Verpackung
Muster
WE-PMI Power-Multilayer-Induktivität, 4.7 µH, 600 mA
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Induktivität4.7 µH
Nennstrom 1600 mA
Nennstrom 2850 mA
Sättigungsstrom250 mA
Gleichstromwiderstand250 mΩ
Eigenresonanzfrequenz30 MHz
TypLow RDC 
Höhe1 mm
Breite1.2 mm
Gleichstromwiderstand312.5 mΩ
VersionSMT 
Pins
MontageartSMT 
WE-TI Tonneninduktivität, 47 µH, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Induktivität47 µH
Sättigungsstrom1200 mA
Eigenresonanzfrequenz10.6 MHz
Höhe8.5 mm
Breite6 mm
Nennstrom1.18 A
Sättigungsstrom 11.2 A
Gleichstromwiderstand340 mΩ
VersionSchrumpfschlauch 
MontageartTHT 
WR-USB Standard Connectors, –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
TypHorizontal - Short Type 
Nennstrom1.5 A
Interface typType A 
AusführungMit Clips 
GenderBuchse 
Pins
MontageartTHT 
Arbeitsspannung30 V (AC)
VerpackungTape and Reel & Mylar