IC-Hersteller Onsemi

IC-Hersteller (103)

Onsemi FL7930 | Demoboard RD-574

Single-Stage Flyback and Boundary-Mode PFC Controller for Lighting

Details

TopologieLeistungsfaktor-Korrektur
Eingangsspannung90-300 V
Schaltfrequenz600 kHz
Ausgang 148 V / 0.6 A
IC-Revision1.0

Beschreibung

RD-574The FL7930B is an active power factor correction (PFC) controller for boost PFC applications that operate in critical conduction mode (CRM). It uses a voltage-mode PWM that compares an internal ramp signal with the error amplifier output to generate a MOSFET turn-off signal. Because the voltage-mode CRM PFC controller does not need rectified AC line voltage information, it saves the power loss of an input voltage sensing network necessary for a current-mode CRM PFC controller.FL7930B provides over-voltage protection (OVP), open-feedback protection, over-current protection (OCP), input-voltage-absent detection, and under-voltage lockout protection (UVLO). The additional OVP pin can be used to shut down the boost power stage when output voltage exceeds OVP level due to the resistors that are connected at INV pin are damaged. The FL7930B can be disabled if the INV pin voltage is lower than 0.45 V and the operating current decreases to a very low level. Using a new variable on-time control method, total harmonic distortion (THD) is lower than in conventional CRM boost PFC ICs.

Eigenschaften

Additional OVP Detection PinVIN-Absent DetectionMaximum Switching Frequency LimitationInternal Soft-Start and Startup without OvershootInternal Total Harmonic Distortion (THD) OptimizerPrecise Adjustable Output Over-Voltage ProtectionOpen-Feedback Protection and Disable FunctionZero Current Detector (ZCD)150 μs Internal Startup TimerMOSFET Over-Current Protection (OCP)Under-Voltage Lockout with 3.5 V HysteresisLow Startup and Operating CurrentTotem-Pole Output with High State Clamp+500/-800 mA Peak Gate Drive Current8-Pin, Small-Outline Package (SOP)

Typische Anwendungen

  • Lighting

Weiterführende Informationen

Artikeldaten

Artikel Nr.
Daten­blatt
Simu­lation
Downloads
Status
Produktserie
Pins
PCB/Kabel/Panel
Modularity
Wire Section
C
VR(V (AC))
Sicherheitsklasse
dV/dt(V/µs)
DF @ 1 kHz(%)
RISO
Raster(mm)
L(mm)
B(mm)
H(mm)
Verpackung
Tol. C
Bauform
Betriebstemperatur
Q(%)
DF(%)
Keramiktyp
Fl(mm)
L(µH)
IR(A)
ISAT(A)
fres(MHz)
Z @ 100 MHz(Ω)
Zmax(Ω)
Testbedingung Zmax
IR 2(mA)
RDC max.(Ω)
Typ
Muster
WR-TBL Series 412MB - 3.50 mm Screwless 45° Entry - 2.08 mm² Wires, 6, Schraublos
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Pins
PCB/Kabel/PanelPCB 
ModularityNein 
Wire Section 14 to 20 (AWG) 2.08 to 0.518 (mm²)
Raster3.5 mm
Länge22.5 mm
VerpackungKarton 
Betriebstemperatur -40 °C up to +105 °C
Nennstrom2 A
Typ45° 
WE-CBF SMT-Ferrit, –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
ProduktserieWE-CBF SMT-Ferrit
Länge1.6 mm
Breite0.8 mm
Höhe0.8 mm
Bauform0603 
Betriebstemperatur -55 °C up to +125 °C
Pad Dimension0.3 mm
Nennstrom0.5 A
Impedanz @ 100 MHz220 Ω
Maximale Impedanz280 Ω
Maximale Impedanz350 MHz 
Nennstrom 21000 mA
Gleichstromwiderstand0.3 Ω
TypBreitband 
WCAP-FTXX Folienkondensatoren, –, Across the mains
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität220 nF
Nennspannung310 V (AC)
SicherheitsklasseX2 
Spannungsanstiegsgeschwindigkeit180 V/µs
Verlustfaktor0.1 %
Isolationswiderstand30 GΩ
Raster15 mm
Länge18 mm
Breite6 mm
Höhe11.5 mm
VerpackungKarton 
Kapazität±10% 
BauformRaster 15 mm 
Betriebstemperatur -40 °C up to +105 °C
WCAP-FTXX Folienkondensatoren, –, Across the mains
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität470 nF
Nennspannung310 V (AC)
SicherheitsklasseX2 
Spannungsanstiegsgeschwindigkeit220 V/µs
Verlustfaktor0.1 %
Isolationswiderstand21.28 GΩ
Raster15 mm
Länge18 mm
Breite8 mm
Höhe14 mm
VerpackungKarton 
Kapazität±10% 
BauformRaster 15 mm 
Betriebstemperatur -40 °C up to +105 °C
WE-LQS SMT-Speicherdrossel, –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Länge6 mm
Breite6 mm
Höhe4.5 mm
Bauform6045 
Betriebstemperatur -40 °C up to +125 °C
Induktivität33 µH
Nennstrom1.8 A
Sättigungsstrom2 A
Eigenresonanzfrequenz12 MHz
WCAP-CSGP MLCCs 10 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität2.2 µF
Nennspannung10 V (AC)
Isolationswiderstand0.05 GΩ
Länge1.6 mm
Breite0.8 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0603 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor10 %
KeramiktypX7R Klasse II 
Pad Dimension0.4 mm
WCAP-CSGP MLCCs 25 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität330 pF
Nennspannung25 V (AC)
Isolationswiderstand10 GΩ
Länge1.6 mm
Breite0.8 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0603 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor3.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.4 mm
WCAP-CSGP MLCCs 25 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität1 µF
Nennspannung25 V (AC)
Isolationswiderstand0.5 GΩ
Länge1.6 mm
Breite0.8 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0603 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor10 %
KeramiktypX7R Klasse II 
Pad Dimension0.4 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität1 nF
Nennspannung50 V (AC)
Isolationswiderstand10 GΩ
Länge1.6 mm
Breite0.8 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0603 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor2.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.4 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität100 nF
Nennspannung50 V (AC)
Isolationswiderstand5 GΩ
Länge1.6 mm
Breite0.8 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0603 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor3 %
KeramiktypX7R Klasse II 
Pad Dimension0.4 mm
WCAP-CSGP MLCCs 25 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität100 pF
Nennspannung25 V (AC)
Isolationswiderstand10 GΩ
Länge2 mm
Breite1.25 mm
Höhe0.6 mm
Verpackung7" Tape & Reel 
Kapazität±5% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Güte1000 %
KeramiktypNP0 Klasse I 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität10 pF
Nennspannung50 V (AC)
Isolationswiderstand10 GΩ
Länge2 mm
Breite1.25 mm
Höhe0.6 mm
Verpackung7" Tape & Reel 
Kapazität±5% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Güte600 %
KeramiktypNP0 Klasse I 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 25 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität470 nF
Nennspannung25 V (AC)
Isolationswiderstand1.1 GΩ
Länge2 mm
Breite1.25 mm
Höhe1.25 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor3.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 25 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität1 µF
Nennspannung25 V (AC)
Isolationswiderstand0.5 GΩ
Länge2 mm
Breite1.25 mm
Höhe1.25 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor5 %
KeramiktypX7R Klasse II 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität1 nF
Nennspannung50 V (AC)
Isolationswiderstand10 GΩ
Länge2 mm
Breite1.25 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor2.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität10 nF
Nennspannung50 V (AC)
Isolationswiderstand10 GΩ
Länge2 mm
Breite1.25 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor2.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität15 nF
Nennspannung50 V (AC)
Isolationswiderstand10 GΩ
Länge2 mm
Breite1.25 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor2.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität22 nF
Nennspannung50 V (AC)
Isolationswiderstand10 GΩ
Länge2 mm
Breite1.25 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor2.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität47 nF
Nennspannung50 V (AC)
Isolationswiderstand10 GΩ
Länge2 mm
Breite1.25 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor2.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität100 nF
Nennspannung50 V (AC)
Isolationswiderstand5 GΩ
Länge2 mm
Breite1.25 mm
Höhe0.8 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor2.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität220 nF
Nennspannung50 V (AC)
Isolationswiderstand2.3 GΩ
Länge2 mm
Breite1.25 mm
Höhe1.25 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor3 %
KeramiktypX7R Klasse II 
Pad Dimension0.5 mm
WCAP-CSGP MLCCs 50 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität220 nF
Nennspannung50 V (AC)
Isolationswiderstand2.3 GΩ
Länge3.2 mm
Breite1.6 mm
Höhe0.95 mm
Verpackung7" Tape & Reel 
Kapazität±10% 
Bauform1206 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor2.5 %
KeramiktypX7R Klasse II 
Pad Dimension0.6 mm
750315757
Power Inductor, –, –
Simu­lation
Downloads
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Produktserie Power Inductor
750315759
PFC Inductor, –, –
Simu­lation
Downloads
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Produktserie PFC Inductor
750315879
Flyback Transformer, –, –
Simu­lation
Downloads
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Produktserie Flyback Transformer