| Topologie | Abwärts- und Aufwärtswandler |
| Eingangsspannung | 1.3-5.5 V |
| Schaltfrequenz | 1.4-2.7 kHz |
| Ausgang 1 | 5 V |
| IC-Revision | E1 |
The TPS63802 is a high efficiency, high output current buck-boost converter. It is used when the input voltage is higher, equal, or lower than the output voltage. Output currents up to 2 A are supported over a wide voltage range. The device limits the peak current at 4.5 A in Boost-Mode and 3.5 A in Buck-Mode. The device is adjusted to the programmed output voltage. It automatically changes from buck to boost operation based on the input voltage. It remains in a 3-cycle buck-boost mode when the input voltage is approximately equal to the output voltage. The transitions happen seamlessly and avoids unwanted toggling within the modes. The TPS63802 comes in a 2 mm x 3 mm package. The device works with tiny passive components to keep the overall solution size small.
1.8 V for Device Start-up
Artikel Nr. | Datenblatt | Simulation | Downloads | Status | Produktserie | L(µH) | IRP,40K(A) | ISAT,30%(A) | RDC typ.(mΩ) | fres(MHz) | VOP(V) | Montageart | Pins | Typ | L(mm) | H(mm) | IR(A) | Arbeitsspannung(V (AC)) | Betriebstemperatur | Muster | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
![]() | WE-MAPI SMT-Speicherdrossel, 1 µH, 10.1 A | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWE-MAPI SMT-Speicherdrossel | Induktivität1 µH | Performance Nennstrom10.1 A | Sättigungsstrom @ 30%11.5 A | Gleichstromwiderstand12 mΩ | Eigenresonanzfrequenz55 MHz | Betriebsspannung80 V | MontageartSMT | Pins2 | – | Länge4 mm | Höhe2 mm | Nennstrom7.2 A | – | Betriebstemperatur -40 °C up to +125 °C | ||||
![]() | WR-PHD Stiftleisten - Einreihig, –, – | Simulation– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWR-PHD Stiftleisten - Einreihig | – | – | – | – | – | – | MontageartTHT | Pins2 | TypGerade | Länge5.08 mm | – | Nennstrom3 A | Arbeitsspannung250 V (AC) | Betriebstemperatur -40 °C up to +105 °C | |||
![]() | WR-PHD Stiftleisten - Einreihig, –, – | Simulation– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWR-PHD Stiftleisten - Einreihig | – | – | – | – | – | – | MontageartTHT | Pins3 | TypGerade | Länge7.62 mm | – | Nennstrom3 A | Arbeitsspannung250 V (AC) | Betriebstemperatur -40 °C up to +105 °C | |||
![]() | WR-PHD Stiftleisten - Einreihig, –, – | Simulation– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWR-PHD Stiftleisten - Einreihig | – | – | – | – | – | – | MontageartTHT | Pins4 | TypGerade | Länge10.16 mm | – | Nennstrom3 A | Arbeitsspannung250 V (AC) | Betriebstemperatur -40 °C up to +105 °C |