| Topologie | Sperrwandler |
| Eingangsspannung | 90-265 V |
| Ausgang 1 | 15 V |
| IC-Revision | 1.0 |
The EVLVIPGAN50WF evaluation board implements a 15 V / 50 W SSR isolated flyback converter developed for general-purpose applications, operating from 90 to 265 VAC.The reference design is built around the VIPERGAN50W, a new advanced offline high-voltage converter by STMicroelectronics with the following features:- 700 V PowerGaN with embedded senseFET (Si) and HV startup;- QR operation with dynamic blanking time and adjustable valley synchronization delay functions, to maximize efficiency at any input line and load conditions;- Valley-lock to ensure constant valley skipping;- Input voltage feedforward compensation for mains-independent OPP intervention;- Adaptive burst mode for advanced power management in light load conditions;- Frequency jittering for EMI suppression.Enhanced system reliability is ensured by the built-in soft-start function and by the following set of protections:- Input OVP (settable);- Brown-in and brown-out (settable);- Output OVP (settable);- Output overload;- OCP LEB;- Embedded thermal shutdown.The EVLVIPGAN50WF is composed of a main board and a daughter board, with schematics shown in Figure 1 and Figure 2 respectively.The main board contains a diode bridge for double wave rectification, an input pi filter for EMI, a flyback transformer, the VIPERGAN50W and all the related components needed for polarization and feature setting on the primary side. On the secondary side, it contains the output capacitors and the output rectifier, realized by a Power MOSFET driven by a synchronous rectifier for efficiency optimization.
Universal input mains range: 90 – 265 VACFrequency: 50-60 HzOutput voltage: 15 VOutput current: 3.35 AStand-by mains consumption: < 85 mW at 230 VACAverage efficiency: > 90%Tight line and load regulation over the entire input and output rangeMeets IEC55022 Class B conducted EMI even with reduced EMI filter, thanks to the frequency jittering featureRoHS compliant
Artikel Nr. | Datenblatt | Simulation | Downloads | Status | Produktserie | C | Tol. C | VR(V (DC)) | Bauform | Betriebstemperatur | DF(%) | RISO | L(mm) | B(mm) | H(mm) | Fl(mm) | Keramiktyp | Verpackung | Sicherheitsklasse | dV/dt(V/µs) | DF @ 1 kHz(%) | Raster(mm) | Qmin. | Q | L(µH) | IR(A) | ISAT,10%(A) | RDC max.(mΩ) | fres(MHz) | Version | Endurance(h) | IRIPPLE(mA) | ILeak(µA) | Ø D(mm) | MusterVerfügbarkeit & Muster | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
![]() | SPECWCAP-CSST Soft Termination, 220 pF, ±10% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSST Soft Termination | Kapazität220 pF | Kapazität±10% | Nennspannung50 V (DC) | Bauform0603 | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor2.5 % | Isolationswiderstand10 GΩ | Länge1.6 mm | Breite0.8 mm | Höhe0.8 mm | Pad Dimension0.4 mm | KeramiktypX7R Klasse II | Verpackung7" Tape & Reel | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen | |||
![]() | SPECWCAP-CSMH Mid and High Voltage, 470 pF, ±10% | Verfügbarkeit – | Downloads8 Dateien | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSMH Mid and High Voltage | Kapazität470 pF | Kapazität±10% | Nennspannung1000 V (DC) | Bauform1206 | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor2.5 % | Isolationswiderstand10 GΩ | Länge3.2 mm | Breite1.6 mm | Höhe1.25 mm | Pad Dimension0.6 mm | KeramiktypX7R Klasse II | Verpackung7" Tape & Reel | – | – | – | – | – | Güte600 | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen | ||
SPECWCAP-CSGP MLCCs 50 V(DC), 1 nF, ±10% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 50 V(DC) | Kapazität1 nF | Kapazität±10% | Nennspannung50 V (DC) | Bauform0603 | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor2.5 % | Isolationswiderstand10 GΩ | Länge1.6 mm | Breite0.8 mm | Höhe0.8 mm | Pad Dimension0.4 mm | KeramiktypX7R Klasse II | Verpackung7" Tape & Reel | – | – | – | – | Güte [1]600 | – | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen | ||||
SPECWCAP-CSGP MLCCs 50 V(DC), 6.8 nF, ±10% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 50 V(DC) | Kapazität6.8 nF | Kapazität±10% | Nennspannung50 V (DC) | Bauform0603 | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor2.5 % | Isolationswiderstand10 GΩ | Länge1.6 mm | Breite0.8 mm | Höhe0.8 mm | Pad Dimension0.4 mm | KeramiktypX7R Klasse II | Verpackung7" Tape & Reel | – | – | – | – | Güte [1]600 | – | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen | ||||
![]() | SPECWCAP-FTXX Folienkondensatoren, 100 nF, ±10% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-FTXX Folienkondensatoren | Kapazität100 nF | Kapazität±10% | Nennspannung310 V (DC) | BauformRaster 10 mm | Betriebstemperatur -40 °C up to +105 °C | – | Isolationswiderstand30 GΩ | Länge13 mm | Breite7 mm | Höhe13 mm | – | – | VerpackungKarton | SicherheitsklasseX2 | Spannungsanstiegsgeschwindigkeit300 V/µs | Verlustfaktor0.1 % | Raster10 mm | – | – | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen | |||
SPECWCAP-CSGP MLCCs 50 V(DC), 100 nF, ±10% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 50 V(DC) | Kapazität100 nF | Kapazität±10% | Nennspannung50 V (DC) | Bauform0603 | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor3 % | Isolationswiderstand5 GΩ | Länge1.6 mm | Breite0.8 mm | Höhe0.8 mm | Pad Dimension0.4 mm | KeramiktypX7R Klasse II | Verpackung7" Tape & Reel | – | – | – | – | Güte [1]600 | – | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen | ||||
SPECWCAP-CSGP MLCCs 25 V(DC), 1 µF, ±10% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 25 V(DC) | Kapazität1 µF | Kapazität±10% | Nennspannung25 V (DC) | Bauform0603 | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor10 % | Isolationswiderstand0.5 GΩ | Länge1.6 mm | Breite0.8 mm | Höhe0.8 mm | Pad Dimension0.4 mm | KeramiktypX7R Klasse II | Verpackung7" Tape & Reel | – | – | – | – | Güte [1]600 | – | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen | ||||
SPECWCAP-CSGP MLCCs 25 V(DC), 4.7 µF, ±10% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 25 V(DC) | Kapazität4.7 µF | Kapazität±10% | Nennspannung25 V (DC) | Bauform1206 | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor7 % | Isolationswiderstand0.1 GΩ | Länge3.2 mm | Breite1.6 mm | Höhe1.6 mm | Pad Dimension0.6 mm | KeramiktypX7R Klasse II | Verpackung7" Tape & Reel | – | – | – | – | Güte [1]600 | – | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen | ||||
SPECWCAP-CSGP MLCCs 25 V(DC), 10 µF, ±10% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 25 V(DC) | Kapazität10 µF | Kapazität±10% | Nennspannung25 V (DC) | Bauform1206 | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor10 % | Isolationswiderstand0.01 GΩ | Länge3.2 mm | Breite1.6 mm | Höhe1.6 mm | Pad Dimension0.5 mm | KeramiktypX7R Klasse II | Verpackung7" Tape & Reel | – | – | – | – | Güte [1]600 | – | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen | ||||
![]() | SPECWCAP-ATG5 Aluminium-Elektrolytkondensatoren, 22 µF, ±20% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-ATG5 Aluminium-Elektrolytkondensatoren | Kapazität22 µF | Kapazität±20% | Nennspannung50 V (DC) | – | – | Verlustfaktor10 % | – | Länge11 mm | – | – | – | – | VerpackungAmmopack | – | – | – | Raster2 mm | – | – | – | – | – | – | – | – | Endurance 2000 | Rippelstrom60 mA | Leckstrom11 µA | Durchmesser5 mm | –Verfügbarkeit prüfen | |||
![]() | SPECWCAP-ATG5 Aluminium-Elektrolytkondensatoren, 47 µF, ±20% | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-ATG5 Aluminium-Elektrolytkondensatoren | Kapazität47 µF | Kapazität±20% | Nennspannung400 V (DC) | – | – | Verlustfaktor15 % | – | Länge25 mm | – | – | – | – | VerpackungAmmopack | – | – | – | Raster7.5 mm | – | – | – | – | – | – | – | – | Endurance 2000 | Rippelstrom300 mA | Leckstrom564 µA | Durchmesser16 mm | –Verfügbarkeit prüfen | |||
![]() | SPECWE-TI Tonneninduktivität, –, – | Verfügbarkeit – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWE-TI Tonneninduktivität | – | – | Nennspannung120 V (DC) | Bauform8095 | Betriebstemperatur -40 °C up to +125 °C | – | – | Länge7.8 mm | Breite7.8 mm | Höhe9.5 mm | – | – | – | – | – | – | – | – | – | Induktivität47 µH | Nennstrom2 A | Sättigungsstrom 12.3 A | Gleichstromwiderstand120 mΩ | Eigenresonanzfrequenz9.1 MHz | VersionGestanzt | – | – | – | – | –Verfügbarkeit prüfen | |||
750841235 | SPECOffline Transformer, –, – | Simulation– | Verfügbarkeit – | Downloads– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | Produktserie Offline Transformer | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | –Verfügbarkeit prüfen |
| Erwartete Verfügbarkeit | Eingehender Bestand | Menge |
|---|---|---|
| Aktuelle Verfügbarkeit | – | – |