Topologie | Drahtlose Energieübertragung |
Eingangsspannung | 20 V |
Ausgang 1 | 12 V / 1.5 A |
IC-Revision | 001 |
BD57015GWL is a stand-alone wireless power receiver IC. The device integrates a fully synchronous rectifier circuit withlow-impedance FETs, Qi compliant and PMA compliantpacket controller, adjustable regulated voltage output, and an open-drain output terminal to communicate with the power transmitter using amplitude modulation. BD57015GWL is targeted at mobile applicationsimplementing wireless charging compliant to Qi Medium Power standard and the PMA standard.
Low Impedance FET rectifier High efficiency fully synchronous rectifier Maximum Input Voltage of 20V Supports Qi standard ver1.2, PMA standard SR1 Automatic Detection of Qi / PMA, or selection byexternal pin Open-Drain output terminal for modulation TX-RX coil Position Gap alarm
Artikel Nr. | Datenblatt | Simulation | Downloads | Produktserie | C | Tol. C | VR (V (DC)) | Bauform | Betriebstemperatur | Q | DF (%) | RISO | Keramiktyp | L (mm) | W (mm) | Fl (mm) | H (mm) | Betätigungskraft (Value) (g) | Elektrische Lebensdauer (Cycles) | Actuator-Farbe | Pins | Reihen | Gender | Typ | IR (A) | Verpackung | Muster | |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
885012006063 | SPEC | 6 Dateien | WCAP-CSGP MLCCs 50 V(DC) | 1 nF | ±5% | 50 | 0603 | -55 bis zu +125 °C | 1000 | – | 10 GΩ | NP0 Klasse I | 1.6 | 0.8 | 0.4 | 0.8 | – | – | – | – | – | – | – | – | 7" Tape & Reel | |||
885012205037 | SPEC | 6 Dateien | WCAP-CSGP MLCCs 16 V(DC) | 100 nF | ±10% | 16 | 0402 | -55 bis zu +125 °C | – | 5 | 5 GΩ | X7R Klasse II | 1 | 0.5 | 0.25 | 0.5 | – | – | – | – | – | – | – | – | 7" Tape & Reel | |||
885012206046 | SPEC | 6 Dateien | WCAP-CSGP MLCCs 16 V(DC) | 100 nF | ±10% | 16 | 0603 | -55 bis zu +125 °C | – | 3.5 | 5 GΩ | X7R Klasse II | 1.6 | 0.8 | 0.4 | 0.8 | – | – | – | – | – | – | – | – | 7" Tape & Reel | |||
885012206071 | SPEC | 6 Dateien | WCAP-CSGP MLCCs 25 V(DC) | 100 nF | ±10% | 25 | 0603 | -55 bis zu +125 °C | – | 3.5 | 5 GΩ | X7R Klasse II | 1.6 | 0.8 | 0.4 | 0.8 | – | – | – | – | – | – | – | – | 7" Tape & Reel | |||
885012206076 | SPEC | 6 Dateien | WCAP-CSGP MLCCs 25 V(DC) | 1 µF | ±10% | 25 | 0603 | -55 bis zu +125 °C | – | 10 | 0.5 GΩ | X7R Klasse II | 1.6 | 0.8 | 0.4 | 0.8 | – | – | – | – | – | – | – | – | 7" Tape & Reel | |||
61301011821 | SPEC | – | 6 Dateien | WR-PHD 2.54 mm Socket Header | – | – | – | – | -40 bis zu +105 °C | – | – | 1000 MΩ | – | 25.9 | – | – | – | – | – | – | 10 | Single | Socket Header | Gerade | 3 | Tray | ||
![]() | 434331013822 | SPEC | – | 6 Dateien | WS-TASU SMT Tact Switch 3.5x2.9 mm side push | – | – | 12 | – | -40 bis zu +85 °C | – | – | 100 MΩ | – | – | – | – | 1.35 | 220 | 100000 | Weiß | – | – | – | – | 0.05 | Tape and Reel | |
61301011121 | SPEC | – | 6 Dateien | WR-PHD 2.54 mm THT Pin Header | – | – | – | – | -40 bis zu +105 °C | – | – | 1000 MΩ | – | 25.4 | – | – | – | – | – | – | 10 | Single | Pin Header | Gerade | 3 | Beutel |
Artikel Nr. | Datenblatt | Simulation | |
---|---|---|---|
885012006063 | SPEC | ||
885012205037 | SPEC | ||
885012206046 | SPEC | ||
885012206071 | SPEC | ||
885012206076 | SPEC | ||
61301011821 | SPEC | – | |
![]() | 434331013822 | SPEC | – |
61301011121 | SPEC | – |
Muster |
---|
Artikel Nr. | Datenblatt | Simulation | Downloads | Produktserie | C | Tol. C | VR (V (DC)) | Bauform | Betriebstemperatur | Q | DF (%) | RISO | Keramiktyp | L (mm) | W (mm) | Fl (mm) | H (mm) | Betätigungskraft (Value) (g) | Elektrische Lebensdauer (Cycles) | Actuator-Farbe | Pins | Reihen | Gender | Typ | IR (A) | Verpackung | Muster |
---|