IC-Hersteller Onsemi

IC-Hersteller (103)

Onsemi NCL30125

Details

TopologieEintaktflusswandler
Eingangsspannung180-264 V
Schaltfrequenz100 kHz
Ausgang 112 V / 25 A
IC-Revision300W lighting Solution with NCL3

Beschreibung

This user’s manual provides elementary information about a two−switch forward converter built with the NCL30125 operated in current−mode control. This controller offers many features to build an energy efficient converter with all the needed protections like cycle−by−cycle current limit with a 500−mV sense voltage, over temperature protection with a dedicated NTC pin and brown−out feature. In addition to the low side MSOFET drive, the controller integrates also a high−side section to drive the floating N−channel power MOSFET. Dedicated pins are available to adjust the switching frequency (RT pin – pin 6) or the soft−start duration (SS pin – pin 7). Finally, a high−voltage current source with Dynamic−Self Supply (DSS) is embedded to quickly start the power supply and maintain the Vcc voltage in light load or standby. The primary−side section drives a transformer whose primary inductance is 3 mH. The energy accumulated in this inductance is sending back to the bulk capacitor thanks to the freewheel components. One of the classical freewheel diode has been replaced by a MOSFET Q3 driven by the controller in order to refresh the bootstrap capacitor. The current is sensed via a 83−m resistance. The switching frequency of 100 kHz and the soft−start duration are set by two individual components (R8 for fSW and C5 for SS). The power stage is made of two switching N−channel transistors Q1 and Q2. These two transistors are switched in same time and seen the input voltage as maximum. In the secondary side, D13 and D15 constitute Rectifier and Freewheel part. The regulation is ensured by a TL431.

Eigenschaften

  • Two−Switch topology current mode control
  • A simple control circuit without a driver transformer
  • Rated Output power: 300 W
  • Standby power: <0.3 W in Universal AC input voltage
  • Full load Efficiency: >88% @ at board end, 230 Vac input
  • Completed protection: OCP,OVP
  • Brown−out protection
  • Switching frequency: ~100 kHz

Typische Anwendungen

  • Lighting

Weiterführende Informationen

Artikeldaten

Artikel Nr.
Daten­blatt
Simu­lation
Downloads
Status
Produktserie
C
VR(V (DC))
Endurance(h)
IRIPPLE(mA)
ILeak(µA)
DF(%)
Raster(mm)
Ø D(mm)
L(mm)
Verpackung
Muster
WCAP-ATG8 Aluminium-Elektrolytkondensatoren, 47 µF, 50 V (DC)
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität47 µF
Nennspannung50 V (DC)
Endurance 2000
Rippelstrom165 mA
Leckstrom23.5 µA
Verlustfaktor10 %
Raster2.5 mm
Durchmesser6.3 mm
Länge11 mm
VerpackungAmmopack 
WCAP-AIG8 Aluminium-Elektrolytkondensatoren, 330 µF, 400 V (DC)
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität330 µF
Nennspannung400 V (DC)
Endurance 2000
Rippelstrom2050 mA
Leckstrom2640 µA
Verlustfaktor20 %
Raster10 mm
Durchmesser30 mm
Länge30 mm
VerpackungTray 
WCAP-ATLI Aluminium-Elektrolytkondensatoren, 560 µF, 35 V (DC)
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität560 µF
Nennspannung35 V (DC)
Endurance 5000
Rippelstrom2040 mA
Leckstrom196 µA
Verlustfaktor9 %
Raster5 mm
Durchmesser10 mm
Länge25 mm
VerpackungAmmopack