| Topologie | Aufwärtswandler |
| Eingangsspannung | 5-20 V |
| Schaltfrequenz | 300-2000 kHz |
| Ausgang 1 | 24 V / 1.4 A |
| IC-Revision | 1 |
The LT8364 is a current mode DC/DC converter with a 60V, 4A switch operating from a 2.8V to 60V input. With a unique single feedback pin architecture it is capable of boost, SEPIC or inverting configurations. Burst Mode operation consumes as low as 9μA quiescent current tomaintain high efficiency at very low output currents, while keeping typical output ripple below 15mV. An external compensation pin allows optimization of loop bandwidth over a wide range of input and output voltages and programmable switching frequencies between 300kHz and 2MHz. A SYNC/MODE pin allows synchronization to an external clock. It can also be used to select between burst or pulse-skip modes of operation with or without Spread Spectrum Frequency Modulation for low EMI. For increased efficiency, a BIAS pin can accept a second input to supply the INTVCC regulator. Additional features include frequency foldback and programmable soft-start to control inductor current during startup.The LT8364 is available in a thermally enhanced 12-lead 4mm × 3mm DFN package or a thermally enhanced 16-lead MSOP package with four pins removed.
Artikel Nr. | Datenblatt | Simulation | Downloads | Status | Produktserie | L(µH) | IR(A) | ISAT1(A) | ISAT2(A) | fres(MHz) | IRP,40K(A) | ISAT,10%(A) | ISAT,30%(A) | Montageart | Z @ 100 MHz(Ω) | Zmax(Ω) | Testbedingung Zmax | IR 2(mA) | RDC max.(mΩ) | Typ | Muster | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
![]() | WE-PMCI Power Molded Chip Induktivität, 0.47 µH, 7.1 A | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWE-PMCI Power Molded Chip Induktivität | Induktivität0.47 µH | Nennstrom7.1 A | Sättigungsstrom 15.15 A | Sättigungsstrom 29.95 A | Eigenresonanzfrequenz90 MHz | Performance Nennstrom7.1 A | Sättigungsstrom 15.15 A | Sättigungsstrom @ 30%9.95 A | MontageartSMT | – | – | – | Nennstrom 23600 mA | Gleichstromwiderstand22 mΩ | – | ||||
![]() | WE-LHMI SMT Speicherdrossel, 2.2 µH, – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWE-LHMI SMT Speicherdrossel | Induktivität2.2 µH | – | – | – | Eigenresonanzfrequenz49 MHz | Performance Nennstrom4.05 A | Sättigungsstrom 14.45 A | Sättigungsstrom @ 30%8.4 A | MontageartSMT | – | – | – | – | Gleichstromwiderstand61 mΩ | – | ||||
![]() | WE-CBF SMT-Ferrit, –, 1.5 A | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWE-CBF SMT-Ferrit | – | Nennstrom1.5 A | – | – | – | – | – | – | MontageartSMT | Impedanz @ 100 MHz600 Ω | Maximale Impedanz700 Ω | Maximale Impedanz150 MHz | Nennstrom 22000 mA | Gleichstromwiderstand150 mΩ | TypHochstrom |