| Topologie | Motor Drive |
| Eingangsspannung | 7-75 V |
| Ausgang 1 | 10 A |
| IC-Revision | 1.0 |
The EVLSPIN9P1-3PH demonstration board is a three-phase power board, which allows to evaluate all STSPIN9P12 features.The board is designed to support a three-shunt or single-shunt current sensing topology.The board can be stacked with an X-NUCLEO MCU control board through ST morpho connectors and drive BLDC/PMSM motors exploiting off-the-shelf firmware libraries.The STSPIN9P12 is a high-density power driver integrating gate drivers and two N-channel power MOSFETs in half-bridge configuration.The device has dedicated input pins for each output and one enable pin. The logic inputs are CMOS/TTL compatible down to 3.3 V for easy interfacing with control devices.
3-phase driver for BLDC/PMSM motorsSTSPIN9P12 power system-in-package integrating gate driver and high-current power MOSFETs with RDS(ON) = 27 mΩ7 V to 75 V operating voltageUp to 10 Arms output currentOperating frequency up to 100 kHzProgrammable output slew rateCompatible with STM32 Nucleo boardsFully compatible with STM32 motor control SDKEquipped with ST ST morphoThree-shunt or single-shunt configurable jumpers for motor current sensing topologyHall / encoder motor sensors connector and circuitPotentiometer available for speed regulationUser LEDOpen-load detectionThermal shutdown, UVLO, and overcurrent protectionBus voltage sensingStandby modeX-NUCLEO form factor with Arduino® connectors (not mounted by default)RoHS compliant
Artikel Nr. | Datenblatt | Simulation | Downloads | Status | Produktserie | λDom typ.(nm) | Farbe | λPeak typ.(nm) | IV typ.(mcd) | VF typ.(V) | Chiptechnologie | 2θ50% typ.(°) | Pins | Typ | Montageart | L(mm) | H(mm) | IR(A) | Arbeitsspannung(V (AC)) | Betriebstemperatur | Muster | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
![]() | WL-SMCW SMT Mono-color Chip LED Waterclear, 570 nm, Hellgrün | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWL-SMCW SMT Mono-color Chip LED Waterclear | dominante Wellenlänge [typ.]570 nm | FarbeHellgrün | Spitzen-Wellenlänge [typ.]572 nm | Lichtstärke [typ.]40 mcd | Durchlassspannung [typ.]2 V | ChiptechnologieAlInGaP | Abstrahlwinkel Phi 0° [typ.]140 ° | – | – | MontageartSMT | Länge1.6 mm | Höhe0.7 mm | – | – | Betriebstemperatur -40 °C up to +85 °C | ||||
![]() | WL-SMCW SMT Mono-color Chip LED Waterclear, 625 nm, Rot | Downloads26 Dateien Strahldaten
| Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWL-SMCW SMT Mono-color Chip LED Waterclear | dominante Wellenlänge [typ.]625 nm | FarbeRot | Spitzen-Wellenlänge [typ.]630 nm | Lichtstärke [typ.]250 mcd | Durchlassspannung [typ.]2 V | ChiptechnologieAlInGaP | Abstrahlwinkel Phi 0° [typ.]140 ° | – | – | MontageartSMT | Länge1.6 mm | Höhe0.7 mm | – | – | Betriebstemperatur -40 °C up to +85 °C | |||
![]() | WR-PHD Stiftleisten - Einreihig, –, – | Simulation– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWR-PHD Stiftleisten - Einreihig | – | – | – | – | – | – | – | Pins2 | TypGerade | MontageartTHT | Länge5.08 mm | – | Nennstrom3 A | Arbeitsspannung250 V (AC) | Betriebstemperatur -40 °C up to +105 °C | |||
![]() | WR-PHD Stiftleisten - Einreihig, –, – | Simulation– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWR-PHD Stiftleisten - Einreihig | – | – | – | – | – | – | – | Pins3 | TypGerade | MontageartTHT | Länge7.62 mm | – | Nennstrom3 A | Arbeitsspannung250 V (AC) | Betriebstemperatur -40 °C up to +105 °C | |||
![]() | WR-PHD Stiftleisten - Einreihig, –, – | Simulation– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWR-PHD Stiftleisten - Einreihig | – | – | – | – | – | – | – | Pins5 | TypGerade | MontageartTHT | Länge12.7 mm | – | Nennstrom3 A | Arbeitsspannung250 V (AC) | Betriebstemperatur -40 °C up to +105 °C |