| Topologie | Leistungsfaktor-Korrektur |
| Schaltfrequenz | 27.4 kHz |
| IC-Revision | 04 |
The 8−pin PFC controller NCL2801 is designed to drive PFC boost stages. It is based on an innovative Valley Count Frequency Fold−back (VCFF) method. The circuit classically operates in Critical conduction Mode (CrM) for high load values. When the load decreases a Discontinuous Conduction Mode DCM is forced by forcing a dead time which, by construction corresponds to a fixed number of valleys. The lower the output power, the higher the number of valleys corresponding to the dead time. After DCM works down to 6th valley switching and if the load continues to decrease, a dead time is continuously added to the 6th valley. The end of additional dead time is synchronized with the drain voltage valley. The maximum switching period is limited to 36.5 s. VCFF maximizes the efficiency during DCM and light load. In particular, the stand−by losses are reduced to a minimum. Like in FCCrM controllers, internal circuitry allows near−unity power factor even when the switching frequency is reduced. Housed in a SO−8 package, the circuit also incorporates the features necessary for robust and compact PFC stages, with few external components.
Artikel Nr. | Datenblatt | Simulation | Downloads | Status | Produktserie | Pins | PCB/Kabel/Panel | Modularity | Typ | Wire Section | C | VR 2(V (DC)) | Sicherheitsklasse | dV/dt(V/µs) | DF @ 1 kHz(%) | RISO | Raster(mm) | Verpackung | Tol. C | Betriebstemperatur | DF(%) | Keramiktyp | Fl(mm) | fres(MHz) | Endurance(h) | IRIPPLE(mA) | ILeak(µA) | Ø D(mm) | IR(A) | L(mH) | RDC max.(mΩ) | VR(V (AC)) | VT(V (AC)) | Material | L(mm) | B(mm) | H(mm) | Montageart | Vin | n | ISAT(A) | RDC1 max(mΩ) | RDC2 max(mΩ) | Bauform | Muster | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
![]() | WR-TBL Series 1317 - Rising Cage Clamp 5.00mm pitch - Horizontal cable entry - THT, 2, Teilbare Druckklemme | Simulation– | Downloads6 Dateien | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | Pins2 | PCB/Kabel/PanelPCB | ModularityNein | TypHorizontal | Wire Section 30 to 12 (AWG) 0.05 to 3.31 (mm²) | – | – | – | – | – | – | Raster5 mm | VerpackungKarton | – | Betriebstemperatur -30 °C up to +120 °C | – | – | – | – | – | – | – | – | Nennstrom22 A | – | – | – | – | – | Länge10 mm | – | – | MontageartTHT | – | – | – | – | – | – | |||
![]() | WR-TBL Series 1317 - Rising Cage Clamp 5.00mm pitch - Horizontal cable entry - THT, 3, Teilbare Druckklemme | Simulation– | Downloads6 Dateien | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | Pins3 | PCB/Kabel/PanelPCB | ModularityNein | TypHorizontal | Wire Section 30 to 12 (AWG) 0.05 to 3.31 (mm²) | – | – | – | – | – | – | Raster5 mm | VerpackungKarton | – | Betriebstemperatur -30 °C up to +120 °C | – | – | – | – | – | – | – | – | Nennstrom22 A | – | – | – | – | – | Länge15 mm | – | – | MontageartTHT | – | – | – | – | – | – | |||
![]() | WE-CMB Stromkompensierte Netzdrossel, 4, – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWE-CMB Stromkompensierte Netzdrossel | Pins4 | – | – | – | – | – | – | – | – | – | – | – | – | – | Betriebstemperatur -40 °C up to +125 °C | – | – | – | – | – | – | – | – | Nennstrom4 A | Induktivität3.3 mH | Gleichstromwiderstand35 mΩ | Nennspannung250 V (AC) | Prüfspannung1500 V (AC) | MaterialMnZn | Länge27.5 mm | Breite18.5 mm | Höhe33 mm | MontageartTHT | – | – | – | – | – | BauformL | ||||
![]() | WE-PFC PFC Chokes, 4, – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWE-PFC PFC Chokes | Pins4 | – | – | – | – | – | – | – | – | – | – | – | – | – | Betriebstemperatur -40 °C up to +125 % | – | – | – | – | – | – | – | – | Nennstrom3 A | Induktivität0.18 mH | – | – | Prüfspannung1500 V (AC) | – | Länge48 mm | Breite43 mm | Höhe32 mm | MontageartTHT | Input Voltage 85 - 265 V (AC) | Übersetzungsverhältnis9:1 | Sättigungsstrom13.2 A | Gleichstromwiderstand 178 mΩ | Gleichstromwiderstand 2200 mΩ | BauformRM14 | ||||
![]() | WCAP-FTXX Folienkondensatoren, –, Across the mains | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-FTXX Folienkondensatoren | – | – | – | – | – | Kapazität330 nF | Nennspannung 2630 V (DC) | SicherheitsklasseX2 | Spannungsanstiegsgeschwindigkeit260 V/µs | Verlustfaktor0.1 % | Isolationswiderstand30 GΩ | Raster12.5 mm | VerpackungKarton | Kapazität±10% | Betriebstemperatur -40 °C up to +105 °C | – | – | – | – | – | – | – | – | – | – | – | Nennspannung310 V (AC) | – | – | Länge15 mm | Breite8.5 mm | Höhe14 mm | MontageartBoxed THT | – | – | – | – | – | BauformRaster 12.5 mm | ||||
![]() | WCAP-FTXX Folienkondensatoren, –, Across the mains | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-FTXX Folienkondensatoren | – | – | – | – | – | Kapazität220 nF | Nennspannung 2630 V (DC) | SicherheitsklasseX2 | Spannungsanstiegsgeschwindigkeit240 V/µs | Verlustfaktor0.1 % | Isolationswiderstand30 GΩ | Raster12.5 mm | VerpackungLose | Kapazität±10% | Betriebstemperatur -40 °C up to +105 °C | – | – | – | – | – | – | – | – | – | – | – | Nennspannung310 V (AC) | – | – | Länge15 mm | Breite7 mm | Höhe12.5 mm | MontageartBoxed THT | – | – | – | – | – | BauformRaster 12.5 mm | ||||
![]() | WE-SI Speicherdrossel, –, – | Simulation– | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWE-SI Speicherdrossel | – | – | – | – | – | – | – | – | – | – | – | Raster0.5 mm | – | – | Betriebstemperatur -40 °C up to +105 °C | – | – | – | Eigenresonanzfrequenz1.8 MHz | – | – | – | Durchmesser23 mm | Nennstrom2 A | Induktivität0.39 mH | Gleichstromwiderstand250 mΩ | – | – | – | Länge23 mm | Breite12.5 mm | Höhe12 mm | MontageartTHT | – | – | Sättigungsstrom0.8 A | – | – | – | |||
![]() | WCAP-ATLI Aluminium-Elektrolytkondensatoren, –, – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-ATLI Aluminium-Elektrolytkondensatoren | – | – | – | – | – | Kapazität22 µF | – | – | – | – | – | Raster2 mm | VerpackungAmmopack | Kapazität±20% | – | Verlustfaktor8 % | – | – | – | Endurance 2000 | Rippelstrom220 mA | Leckstrom11 µA | Durchmesser5 mm | – | – | – | Nennspannung50 V (AC) | – | – | Länge11 mm | – | – | – | – | – | – | – | – | – | ||||
| WCAP-CSGP MLCCs 50 V(DC), –, – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 50 V(DC) | – | – | – | – | – | Kapazität1 nF | – | – | – | – | Isolationswiderstand10 GΩ | – | Verpackung7" Tape & Reel | Kapazität±10% | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor2.5 % | KeramiktypX7R Klasse II | Pad Dimension0.4 mm | – | – | – | – | – | – | – | – | Nennspannung50 V (AC) | – | – | Länge1.6 mm | Breite0.8 mm | Höhe0.8 mm | – | – | – | – | – | – | Bauform0603 | |||||
| WCAP-CSGP MLCCs 25 V(DC), –, – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 25 V(DC) | – | – | – | – | – | Kapazität330 nF | – | – | – | – | Isolationswiderstand1.5 GΩ | – | Verpackung7" Tape & Reel | Kapazität±10% | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor3.5 % | KeramiktypX7R Klasse II | Pad Dimension0.6 mm | – | – | – | – | – | – | – | – | Nennspannung25 V (AC) | – | – | Länge3.2 mm | Breite1.6 mm | Höhe0.95 mm | – | – | – | – | – | – | Bauform1206 | |||||
| WCAP-CSGP MLCCs 25 V(DC), –, – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 25 V(DC) | – | – | – | – | – | Kapazität2.2 µF | – | – | – | – | Isolationswiderstand0.2 GΩ | – | Verpackung7" Tape & Reel | Kapazität±10% | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor3.5 % | KeramiktypX7R Klasse II | Pad Dimension0.6 mm | – | – | – | – | – | – | – | – | Nennspannung25 V (AC) | – | – | Länge3.2 mm | Breite1.6 mm | Höhe1.6 mm | – | – | – | – | – | – | Bauform1206 | |||||
| WCAP-CSGP MLCCs 50 V(DC), –, – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-CSGP MLCCs 50 V(DC) | – | – | – | – | – | Kapazität100 nF | – | – | – | – | Isolationswiderstand5 GΩ | – | Verpackung7" Tape & Reel | Kapazität±10% | Betriebstemperatur -55 °C up to +125 °C | Verlustfaktor2.5 % | KeramiktypX7R Klasse II | Pad Dimension0.6 mm | – | – | – | – | – | – | – | – | Nennspannung50 V (AC) | – | – | Länge3.2 mm | Breite1.6 mm | Höhe0.8 mm | – | – | – | – | – | – | Bauform1206 | |||||
![]() | WCAP-FTBP Folienkondensatoren, –, – | Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre. | ProduktserieWCAP-FTBP Folienkondensatoren | – | – | – | – | – | Kapazität150 nF | – | – | Spannungsanstiegsgeschwindigkeit200 V/µs | Verlustfaktor0.1 % | Isolationswiderstand30 GΩ | Raster15 mm | VerpackungKarton | Kapazität±5% | Betriebstemperatur -40 °C up to +105 °C | – | – | – | – | – | – | – | – | – | – | – | Nennspannung630 V (AC) | – | – | Länge18 mm | Breite7 mm | Höhe13 mm | – | – | – | – | – | – | BauformRaster 15 mm |