IC-Hersteller Analog Devices

IC-Hersteller (103)

Analog Devices LTC4331 | Demoboard EVAL-CN0564 - ARDZ

Robust SPI/I2C Communications for Industrial Applications

Details

TopologieSonstige Topologie

Beschreibung

The LTC4331 is a point-to-point SMBus compatible I2C slave device extender designed for operation in high noise industrial environments. Using a ±60V fault protected differential transceiver, the LTC4331 can extend an I2C/SMBus bus, including SMBALERT and a control signal, over a single twisted pair differential link up to 1200m. With an extended common mode operating range the solution provides tolerance to large ground differences between nodes. For EMI sensitive environments, a slew rate control pin reduces the EMI emitted from the differential link.In addition, the LTC4331 can act as an I2C to I2C bridge allowing independent bus frequencies between the local and remote networks. The solution is completely transparent to the master requiring no additional code in most cases; however, a control interface is provided for additional configuration and fault monitoring.A master controller fully supporting SCL clock-stretching is strongly recommended.

Eigenschaften

  • Up to 1MHz Serial Clock, Fast-mode Plus (Fm+)
  • Selectable Link Baud Rates Extend I2C Up to 1200m
  • Protected from Overvoltage Line Faults to ±60V
  • ±40kV ESD on Link Pins
  • IEC Level 4 ESD ±8kV and EFT ±5kV on Link Pins
  • Extended Common Mode Range: ±15V
  • Remote Interrupt/SMBALERT and Control Signals
  • Low EMI Mode
  • SMBus 3.0 Compatible
  • I2C Idle Detection, and Stuck Bus Protection
  • I2C Device Address Sharing
  • 3V to 5.5V Supply Voltage
  • 1.62V to 5.5V Logic Supply
  • 4mm × 5mm 20-Lead QFN package

Typische Anwendungen

  • Lighting and Sound System Control
  • Industrial Control and Sensors

Weiterführende Informationen

Artikeldaten

Artikel Nr.
Daten­blatt
Simu­lation
Downloads
Status
Produktserie
λDom typ.(nm)
Emittierte Farbe
λPeak typ.(nm)
IV typ.(mcd)
VF typ.(V)
Chiptechnologie
50% typ.(°)
C
Tol. C
VR(V (DC))
Bauform
Betriebstemperatur
DF(%)
RISO
Keramiktyp
L(mm)
B(mm)
H(mm)
Fl(mm)
Verpackung
Pins
Typ
Montageart
IR(A)
Arbeitsspannung(V (AC))
Muster
WL-SMCW SMT Mono-color Chip LED Waterclear, 525 nm, Grün
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
dominante Wellenlänge [typ.]525 nm
Emittierte FarbeGrün 
Spitzen-Wellenlänge [typ.]515 nm
Lichtstärke [typ.]430 mcd
Durchlassspannung [typ.]3.2 V
ChiptechnologieInGaN 
Abstrahlwinkel Phi 0° [typ.]140 °
Bauform0603 
Betriebstemperatur -40 °C up to +85 °C
Länge1.6 mm
Breite0.8 mm
Höhe0.7 mm
VerpackungTape and Reel 
MontageartSMT 
WCAP-CSGP MLCCs 25 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität1 µF
Kapazität±10% 
Nennspannung25 V (DC)
Bauform0603 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor10 %
Isolationswiderstand0.5 GΩ
KeramiktypX7R Klasse II 
Länge1.6 mm
Breite0.8 mm
Höhe0.8 mm
Pad Dimension0.4 mm
Verpackung7" Tape & Reel 
WCAP-CSGP MLCCs 10 V(DC), –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Kapazität10 µF
Kapazität±10% 
Nennspannung10 V (DC)
Bauform0805 
Betriebstemperatur -55 °C up to +125 °C
Verlustfaktor10 %
Isolationswiderstand0.01 GΩ
KeramiktypX7R Klasse II 
Länge2 mm
Breite1.25 mm
Höhe1.25 mm
Pad Dimension0.5 mm
Verpackung7" Tape & Reel 
WR-PHD Stiftleisten - Einreihig, –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Betriebstemperatur -40 °C up to +105 °C
Isolationswiderstand1000 MΩ
Länge7.62 mm
VerpackungBeutel 
Pins
TypGerade 
MontageartTHT 
Nennstrom3 A
Arbeitsspannung250 V (AC)
WR-PHD Stiftleisten - Zweireihig, –, –
Simu­lation
Status Aktivi| Produktion ist aktiv. Erwartete Lebenszeit: >10 Jahre.
Betriebstemperatur -40 °C up to +105 °C
Isolationswiderstand1000 MΩ
Länge5.08 mm
VerpackungBeutel 
Pins
TypGerade 
MontageartTHT 
Nennstrom3 A
Arbeitsspannung250 V (AC)