de

Warenkorb

Ihr Warenkorb ist leer.

IC-Referenzdesignsuche

MaxLinear SP335

RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION

Details

TopologieSonstige Topologie
IC-Revision1.0.0

Beschreibung

The SP335 is an advanced multiprotocol transceiver supporting RS-232, RS-485, and RS-422 serial standards. Integrated cable termination and multiple configuration modes allow all three protocols to be used interchangeably over a single cable or connector with no additional switching components. Full operation requires only four external charge pump capacitors.

The RS-485/RS-232 mode pin selects RS-485 mode when high, and RS-232 mode when low. In RS-485 mode, the TERM pin enables the differential 120Ω termination, and the HALF/FULL pin configures the transceiver as either half or full duplex.

The high speed drivers operate up to 20Mbps in RS-485/422 modes, and up to 1Mbps in RS-232 mode. All drivers can be slew limited to 250kbps in any mode to minimize electromagnetic interference (EMI) by setting the dedicated SLEW pin low.

All transmitter outputs and receiver inputs feature robust electrostatic discharge (ESD) protection to ±15kV IEC 61000-4-2 Airgap, ±15kV Human Body Model (HBM) and ±8kV IEC 61000-4-2 Contact. Each receiver output has full fail-safe protection to avoid system lockup, oscillation, or indeterminate states by defaulting to logic-high output level when the inputs are open, shorted, or terminated but undriven. No external biasing resistors are required.

The RS-232 receiver inputs include a 5kΩ pull-down to ground when in RS-232 mode. The RS-485/422 receiver inputs are high impedance (>96kΩ when termination is disabled), allowing up to 256 devices on a single communication bus (1/8th unit load).

The SP335 operates from a single power supply, either 3.3V or 5V, with low idle current. The shutdown mode consumes less than 1µA in low power standby operation with RS-232 receivers enabled.

Eigenschaften

  • Pin-Selectable Cable Termination
  • No External Resistors Required for RS-485/422Termination or Biasing
  • Robust ESD Protection:! ±15kV IEC 61000-4-2 Air Gap Discharge! ± 8kV IEC 61000-4-2 Contact Discharge! ±15kV Human Body Model (HBM)
  • 20Mbps RS-485 and 1Mbps RS-232 Data Rates
  • Pin-Selectable 250kbps Slew Limiting
  • Single Supply Operation from +3V to +5.5V
  • 1.65V to 5.5V Logic Interface VL pin
  • 2 Drivers, 2 Receivers RS-232/V.28
  • 1 Driver, 1 Receiver RS-485/422! Full or Half Duplex Configuration! 1/8th Unit Load, up to 256 receivers on bus
  • RS-485/422 Enhanced Receiver Fail-safe for open,shorted, or terminated but idle inputs
  • 10nA Shutdown Supply Current (typical)
  • Small 32 QFN package (5mm x 5mm)

Typische Anwendungen

  • Industrial and Process Control Equipment
  • Industrial and Single Board Computers
  • Software Programmable Serial Ports􀀃
  • Building Security and Automation
  • Point-Of-Sale Equipment
  • HVAC Controls and Networking Equipment

Weiterführende Informationen

Artikeldaten

Artikel Nr. Daten­blatt Downloads ProduktseriePinsReihenGenderTypIR
(A)
VerpackungMontageart Muster
61300411121SPEC
6 Dateien WR-PHD 2.54 mm THT Pin Header 4 Single Pin Header Gerade 3 Beutel THT
61300421121SPEC
6 Dateien WR-PHD 2.54 mm THT Dual Pin Header 4 Dual Pin Header Board Stacker 3 Beutel THT
61300821121SPEC
6 Dateien WR-PHD 2.54 mm THT Dual Pin Header 8 Dual Pin Header Board Stacker 3 Beutel THT
618009211721SPEC
6 Dateien WR-DSUB 8.08 mm Male Angled PCB Connector w/o Hex Screw 9 Männlich Angled 3 Tray
61301221121SPEC
6 Dateien WR-PHD 2.54 mm THT Dual Pin Header 12 Dual Pin Header Board Stacker 3 Beutel THT
61301211121SPEC
6 Dateien WR-PHD 2.54 mm THT Pin Header 12 Single Pin Header Gerade 3 Beutel THT
Muster
Artikel Nr. Daten­blatt Downloads ProduktseriePinsReihenGenderTypIR
(A)
VerpackungMontageart Muster